☰ 🔍
🖊️Ask a Question
Electrical Engineering

Finished tolerance on 10 cm. long st. edge on surface of head shall be? (i) 0 to 0.1 mm (ii) 0 to 0.2 mm (iii) 0 to 0.4 mm* (iv) 0 to 0.3 mm

by 1 view
Finished tolerance on 10 cm. long st. edge on surface of head shall be?  (i) 0 to 0.1 mm
 (ii) 0 to 0.2 mm
 (iii) 0 to 0.4 mm*
 (iv) 0 to 0.3 mm
0 like 0 dislike

1 Answer

by
(iii) 0 to 0.4 mm*
0 like 0 dislike

Related questions

by ayush dekate asked Jul 31, 2021 1 view
Finished tolerance on 10 cm long st. edge at the centre on gauge side shall be? (i) ± 0.4 mm (ii) ± 0.1 mm (iii) ± 0.2 mm (iv) ± 0.3 mm*

Finished tolerance on 10 cm long st. edge at the centre on gauge side shall be? (i) ± 0.4 mm (ii) ± 0.1 mm (iii) ± 0.2 mm (iv) ± 0.3 mm*
Answer : iv) ± 0.3 mm*...

View solution
0 like 0 dislike
1 answer
by ayush dekate asked Jul 31, 2021 0 views
Finished tolerance on 1 Mt. long st. edge on surface of head shall be? (i) 0 to .1 mm (ii) 1 to 1.5 mm (iii) 0 mm (iv) 0 to 1 mm*

Finished tolerance on 1 Mt. long st. edge on surface of head shall be? (i) 0 to .1 mm (ii) 1 to 1.5 mm (iii) 0 mm (iv) 0 to 1 mm*
Answer : (iv) 0 to 1 mm*...

View solution
0 like 0 dislike
1 answer
by ayush dekate asked Jul 31, 2021 0 views
Finished tolerance on 1 Mt. st. edge at the centre on gauge side shall be? (i) ± 0.2 mm (ii) ± 0.3 mm (iii) ± 0.5 mm* (iv) ± 1.0 mm

Finished tolerance on 1 Mt. st. edge at the centre on gauge side shall be? (i) ± 0.2 mm (ii) ± 0.3 mm (iii) ± 0.5 mm* (iv) ± 1.0 mm
Answer : (iii) ± 0.5 mm*...

View solution
0 like 0 dislike
1 answer
by ayush dekate asked Jul 31, 2021 0 views
Marking on weld should be done (i) On centre of the rail head (ii) 10 mm below the top surface of rail head.* (iii) 10 mm above the bottom surface of rail head. (iv) None of the above

Marking on weld should be done (i) On centre of the rail head (ii) 10 mm below the top surface of rail head.* (iii) 10 mm above the bottom surface of rail head. (iv) None of the above
Answer : ii) 10 mm below the top surface of rail head.*...

View solution
0 like 0 dislike
1 answer
by ayush dekate asked Jul 31, 2021 0 views
Finishing tolerances are measured by? (i) On 30 cm scale (ii) 1 MT straightedge or 10 CM straightedge.* (iii) On 15 cm straight edge (iv) On 30 cm straight edge

Finishing tolerances are measured by? (i) On 30 cm scale (ii) 1 MT straightedge or 10 CM straightedge.* (iii) On 15 cm straight edge (iv) On 30 cm straight edge
Answer : (ii) 1 MT straightedge or 10 CM straightedge.*...

View solution
0 like 0 dislike
1 answer

50.5k questions

47.1k answers

240 comments

7.0k users

© 2025 Question Answer