During periodic testing of an AT weld with 700 probe, a bunch of moving signals of less than 40% but more than 10% is observed in the head of weld, the joint will be. (i) Good joint.* (ii) DFWR (iii) DFWO (iv) OBSW

Question

Question Answer

🔍

🖊️Ask a Question

Electrical Engineering

Question Answer

During periodic testing of an AT weld with 700 probe, a bunch of moving signals of less than 40% but more than 10% is observed in the head of weld, the joint will be. (i) Good joint.* (ii) DFWR (iii) DFWO (iv) OBSW

by ayush dekate asked Jul 31, 2021 1 view

During periodic testing of an AT weld with 700 probe, a bunch of moving signals of

less than 40% but more than 10% is observed in the head of weld, the joint will be.
(i) Good joint.*
(ii) DFWR
(iii) DFWO
(iv) OBSW

1 Answer

Related questions

by ayush dekate asked Jul 31, 2021 2 views

On a branch line one new AT Weld with 00 probe shows a signal of 58 is. (i) DFWO* (ii) DFWR (iii) IMRW (iv) OBSW

On a branch line one new AT Weld with 00 probe shows a signal of 58 is. (i) DFWO* (ii) DFWR (iii) IMRW (iv) OBSW
Answer : i) DFWO*...

View solution

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 1 view

By 00 probe in AT weld testing with normal gain setting. (i) Area below N.axis can be tested. (ii) Area below N.axis can not be tested.* (iii) Only web below N.axis can be tested. (iv) All above are correct.

By 00 probe in AT weld testing with normal gain setting. (i) Area below N.axis can be tested. (ii) Area below N.axis can not be tested.* (iii) Only web below N.axis can be tested. (iv) All above are correct.
Answer : (ii) Area below N.axis can not be tested.*...

View solution

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 2 views

After declare good in USFD testing what is the joggling criteria ? (i) Joggle will be open from the AT weld* (ii) Joggling with two far end bolting (iii) joggling with four tight bold (iv) None of the above

After declare good in USFD testing what is the joggling criteria ? (i) Joggle will be open from the AT weld* (ii) Joggling with two far end bolting (iii) joggling with four tight bold (iv) None of the above
Answer : (i) Joggle will be open from the AT weld*...

View solution

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 1 view

Side looking 700 2MHZ probe is tested for detecting. (i) Flaw in head (ii) Flaw in web (iii) Half moon crack in flange.* (iv) For all above.

Side looking 700 2MHZ probe is tested for detecting. (i) Flaw in head (ii) Flaw in web (iii) Half moon crack in flange.* (iv) For all above.
Answer : iii) Half moon crack in flange...

View solution

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 0 views

Defect of low joint is due to? (i) Excess height (ii) Early trimming of weld (iii) Early grinding of weld (iv) Nil/Less provision of height during alignment.

Defect of low joint is due to? (i) Excess height (ii) Early trimming of weld (iii) Early grinding of weld (iv) Nil/Less provision of height during alignment.
Answer : (iv) Nil/Less provision of height during alignment....

View solution

0 like 0 dislike

1 answer

ayush dekate · Answer 1 · 2021-07-31T16:52:40+0000

by ayush dekate answered Jul 31, 2021

i) Good joint.*

During periodic testing of an AT weld with 700 probe, a bunch of moving signals of less than 40% but more than 10% is observed in the head of weld, the joint will be. (i) Good joint.* (ii) DFWR (iii) DFWO (iv) OBSW

Please log in or register to add a comment.

1 Answer

Please log in or register to add a comment.

Related questions