Question Answer

🔍

🖊️Ask a Question

Electrical Engineering

Question Answer

Marking on weld should be done which side? (i) Non gauge face side of A.T. weld * (ii) Gauge face side of A.T. weld (iii) On web of non gauge face side of A.T. weld (iv) On web of gauge face side of A.T. weld

by ayush dekate asked Jul 31, 2021 0 views

Marking on weld should be done which side?
(i) Non gauge face side of A.T. weld *
(ii) Gauge face side of A.T. weld
(iii) On web of non gauge face side of A.T. weld
(iv) On web of gauge face side of A.T. weld

1 Answer

by ayush dekate answered Jul 31, 2021

(i) Non gauge face side of A.T. weld

Related questions

by ayush dekate asked Jul 31, 2021 0 views

Marking on weld should be done (i) On centre of the rail head (ii) 10 mm below the top surface of rail head.* (iii) 10 mm above the bottom surface of rail head. (iv) None of the above

Marking on weld should be done (i) On centre of the rail head (ii) 10 mm below the top surface of rail head.* (iii) 10 mm above the bottom surface of rail head. (iv) None of the above
Answer : ii) 10 mm below the top surface of rail head.*...

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 0 views

Painting of weld is done up to (i) 10 CM minimum both side of weld & on welded surface .* (ii) 15 CM minimum both side of weld & on welded surface (iii) 20 CM minimum both side of weld & on welded surface (iv) None of the above

Painting of weld is done up to (i) 10 CM minimum both side of weld & on welded surface .* (ii) 15 CM minimum both side of weld & on welded surface (iii) 20 CM minimum both side of weld & on welded surface (iv) None of the above
Answer : (i) 10 CM minimum both side of weld & on welded surface .*...

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 0 views

Marking of DFWO weld is. (i) Two red point circle on both faces of weld.* (ii) Two red point cross on both faces of weld. (iii) One red point circle on both faces of weld. (iv) None of the above.

Marking of DFWO weld is. (i) Two red point circle on both faces of weld.* (ii) Two red point cross on both faces of weld. (iii) One red point circle on both faces of weld. (iv) None of the above.
Answer : i) Two red point circle on both faces of weld.*...

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 0 views

Trimming of AT weld should be done by ? (i) Chisel (ii) Trimmer* (iii) Both (iv) None of the above

Trimming of AT weld should be done by ? (i) Chisel (ii) Trimmer* (iii) Both (iv) None of the above
Answer : ii) Trimmer*...

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 0 views

In how many time final grinding should be done of new AT weld ? (i) Just after the welding (ii) After 8 hrs of welding (iii) With in 24 hrs* (iv) None of the above

In how many time final grinding should be done of new AT weld ? (i) Just after the welding (ii) After 8 hrs of welding (iii) With in 24 hrs* (iv) None of the above
Answer : iii) With in 24 hrs*...

0 like 0 dislike

1 answer