Defect of low joint is due to? (i) Excess height (ii) Early trimming of weld (iii) Early grinding of weld (iv) Nil/Less provision of height during alignment.

Question

Question Answer

🔍

🖊️Ask a Question

Electrical Engineering

Question Answer

Defect of low joint is due to? (i) Excess height (ii) Early trimming of weld (iii) Early grinding of weld (iv) Nil/Less provision of height during alignment.

by ayush dekate asked Jul 31, 2021 0 views

Defect of low joint is due to?
(i) Excess height
(ii) Early trimming of weld
(iii) Early grinding of weld
(iv) Nil/Less provision of height during alignment.

1 Answer

Related questions

by ayush dekate asked Jul 31, 2021 0 views

Defect of High joint is due to ? (i) Early trimming of weld (ii) Excess provision of height during alignment.* (iii) Early grinding of weld (iv) None of above

Defect of High joint is due to ? (i) Early trimming of weld (ii) Excess provision of height during alignment.* (iii) Early grinding of weld (iv) None of above
Answer : (ii) Excess provision of height during alignment....

View solution

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 0 views

Defect of cracks in weld is mainly due to? (i) Early opening of mould.* (ii) Early trimming of weld (iii) Early grinding of weld (iv) None of above

Defect of cracks in weld is mainly due to? (i) Early opening of mould.* (ii) Early trimming of weld (iii) Early grinding of weld (iv) None of above
Answer : (i) Early opening of mould.*...

View solution

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 2 views

During periodic testing of an AT weld with 700 probe, a bunch of moving signals of less than 40% but more than 10% is observed in the head of weld, the joint will be. (i) Good joint.* (ii) DFWR (iii) DFWO (iv) OBSW

During periodic testing of an AT weld with 700 probe, a bunch of moving signals of less than 40% but more than 10% is observed in the head of weld, the joint will be. (i) Good joint.* (ii) DFWR (iii) DFWO (iv) OBSW
Answer : i) Good joint.*...

View solution

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 0 views

Defect of lack of fusion is mainly due to? (i) Improper heating.* (ii) Improper Gap (iii) Improper grinding (iv) None of above

Defect of lack of fusion is mainly due to? (i) Improper heating.* (ii) Improper Gap (iii) Improper grinding (iv) None of above
Answer : (i) Improper heating.*...

View solution

0 like 0 dislike

1 answer

by ayush dekate asked Jul 31, 2021 0 views

Trimming of AT weld should be done by ? (i) Chisel (ii) Trimmer* (iii) Both (iv) None of the above

Trimming of AT weld should be done by ? (i) Chisel (ii) Trimmer* (iii) Both (iv) None of the above
Answer : ii) Trimmer*...

View solution

0 like 0 dislike

1 answer

ayush dekate · Answer 1 · 2021-07-31T15:51:36+0000

by ayush dekate answered Jul 31, 2021

(iv) Nil/Less provision of height during alignment.

Defect of low joint is due to? (i) Excess height (ii) Early trimming of weld (iii) Early grinding of weld (iv) Nil/Less provision of height during alignment.

Please log in or register to add a comment.

1 Answer

Please log in or register to add a comment.

Related questions